5/17/2023 0 Comments Skateboard grip tapeWith enough pressure and rubbing, it will wear right through the grip tape and technically trim the grip without using a razor. In that case, you can take your truck and grind it against the edge of the board once the grip tape is applied. In some situations, you’ll be setting up a new deck while you’re out skating and you don’t have a blade on hand. How Do You Apply Grip Tape Without A Razor? Although I would start the cut with a blade, cutting out the remainder of the design may be easier with scissors depending on how many intricate details there are. The only time I would opt for scissors over a blade is when I am cutting a larger design in the grip tape. However, when trimming excess grip tape off your deck, using a blade is much easier for cutting smooth edges around the grip tape. If you have a very sharp pair of scissors, it is possible to cut your grip tape with them. If you are wanting to put a new sheet of grip on your board, removing the old grip tape with a hairdryer is your only option. This will make the new grip peel off quickly and become useless. Unfortunately, you cannot put new grip tape over existing grip tape since the adhesive of the new grip tape will not stick well to the old grip tape. Once all the grip tape is removed (along with any small remnants), you can either reapply a new sheet of grip tape or use goo-gone to remove the remaining adhesive if you plan to hang your deck on the wall. That’s where a bit of patience comes in handy as you’ll simply need to reheat the ripped area, and continue peeling until all of the grip tape is lifted. To make life easy, standing on your deck as you peel gives better leverage while peeling.ĭepending on the type of grip tape you’re using, it may rip as you go. From there, carefully peel back the rest of your grip tape using the small flap you lifted with your blade. With this small flap peeled up, use your hairdryer to heat up the rest of the grip tape until it is warm to the touch. Once the grip tape is warm to the touch, take your blade and peel up the grip tape along the edges of where you heated until there is enough to hold onto. After about 30 seconds the grip tape will warm up enough that the adhesive will loosen. To start, you’ll need the following items:įirst, take your hairdryer to the hottest setting and heat up the grip tape along one end of your skateboard. With the help of a hairdryer, you can peel off an old sheet of grip tape pretty quickly. Now if you have an old deck that you’re turning into a cruiser, are wanting to hang your deck on the wall, or have just trashed your grip tape from dark slides, removing and replacing the grip tape is a good idea. Using the precut edges of your grip tape is a super-easy way to make perfectly straight cuts in your grip tape designs since it’s already done for you! How To Remove Grip Tape From An Old Skateboard Deck The standard size of grip tape is 9×33″, which is great for most standard-sized decks, but will be small for wider cruiser-style skateboards. Just remember to get an 11×33″ sheet of grip if you have a skateboard wider than 9″ in width. Regardless of the size or the width of your deck, the gripping process will be the same. I love Mob because it’s perforated and makes air bubbles easy to avoid however, there are a handful of other grip tapes I recommend here in my guide to the best grip tapes. I’ll be gripping my 10.5″ cruiser deck in this example using Mob Grip Tape. To start things off, let’s break down the easy steps to apply grip tape to a fresh skateboard. How To Apply Grip Tape To A Skateboard – Step By Step So whether you’re looking to apply grip tape to a new skateboard deck, make custom grip tape designs, or replace the grip tape on your old deck, we’re going to break it all down here. Although the first few times I gripped a skateboard all those years ago certainly wasn’t my best work, I now have a different grip technique that’s easy to do, even if this is your first time applying grip tape. I remember when I first learned how to apply grip tape to a skateboard I felt a bit stressed out that I would mess it up, get air bubbles, or make it look completely janked.
0 Comments
Leave a Reply. |